How to remove the door from the hinges on the balcony and loggia?

During repairs, the old balcony door is often replaced with a new one. Dismantling does not require special skills, and even a beginner can handle it. If the door is removed correctly, it can be replaced at any time or used in another room.

If done incorrectly, you can deform the wall and even the doorway. Doors are made from a variety of materials, and this is one of the factors that affects the dismantling of the door structure. Consider how best to remove doors from their hinges in the space of a loggia or balcony.

In fact, you can remove the door in just a few seconds.

Dismantling of an old door is most often done when:

• the door surface is damaged and cannot provide protection from cold air or street noise;

• the door lock moves slightly away and no longer adjoins tightly to the opening;

• the door is bent, or a double-glazed window is broken;

• the curtains are wiped off, and they urgently need to be replaced;

• renovations are underway and the doors need to be changed to match the new style.

The reason for the removal of structures may be different, but this procedure is always carried out according to special rules.

1. It is better to change plastic doors in the warm season.

2. If you are going to completely replace a block made of wood or plastic, then a new box is needed. In this case, the old box must first be removed.

3. It is better to remove doors that are heavy with two people. One person will hold the doors, and the other will take over the dismantling work.

To quickly remove the doors, you will need an appropriate set of tools.

To remove wooden structures, you need:

• strong crowbar or good pry bar;

• Phillips screwdrivers, as well as tools with a straight tip;

• axe;

• a hacksaw with fine teeth (a butt saw will also work);

• hammer.

Using these tools, you can easily disassemble the door frame without hitting the walls. Of course, experienced specialists can also use a drill or screwdriver, but the presented set will definitely be at hand for anyone.

To dismantle plastic structures, you will need:

• good pliers and pliers;

• a lever in the form of a pry bar, sturdy board or crowbar;

• a nail with a blunt end or a thin drift;

• several hex screwdrivers;

• chisel and knife.

When all the necessary devices are at hand, it is necessary to understand what stages the removal of such structures consists of.

When a door is removed from a plastic profile, it is necessary to first expose the upper and lower hinges. The plugs must be slightly pry off with a knife and pulled out. After that, we open the door. Insert a nail or punch into the loop at the top and, gently tapping, remove the axial cylinder. If this part does not reach freely, you need to clamp the cylinder from above and pull it out with pliers. In this case, the point of the nail or punch should not be in the groove.

Then the door needs to be slightly opened 90 degrees and raised up. The lower pin is built into the mount, so it cannot be disassembled. To remove the doors from the lower hinge, the assistant must hold the door, and the craftsman pull the pin out with a board or crowbar. The board or scrap must first be wrapped with a cloth, this will not deform the lower part of the door. Use the lever to rest on the floor and pry the lower part of the door with it. The door tilts slightly to the side, after which the lower cylinder can be pulled out.

If the door frame itself is defective, then it will also have to be removed.

1. First you need to get rid of the platbands. You can unscrew the platbands with a screwdriver, knife or spatula. Platbands are very easy to move away from the box, as they are part of the kit.

2. Then you need to remove the slopes in the inner box.

3. After that, the space should be cleaned from the remaining foam.

4. Then the box fasteners are disassembled. For these purposes, a screwdriver or screwdriver is used.

5. After getting rid of the box from the fasteners, you can remove the frame. A scrap or a pry bar is inserted into the slot between the box and the wall, after which you need to pull towards the adjoining room. The box breaks out easily.

6. The last step is to clean the wall from the remaining foam and fasteners.

Removing wood doors is different from removing a plastic model.

First you need to open the doors. Then a crowbar is inserted between the gaps at the bottom of the door. Then the door can be removed from the curtains. However, problems can arise if the hinges are deformed or corroded. There are two ways out of this situation.

1. The hinges should be generously lubricated with oil. To do this, oil is dripped onto the hinges, after which you need to start opening and closing the door - this way the impregnation will enter all parts of the hinge. If this method does not help, you can use a solvent. The agent is sprayed on the curtains, after which aggressive chemicals begin to corrode the rust.

2. If the hinges are bent, then the entire structure is dismantled together with the hinges. First, you need to remove the paint from the mountings, unscrew the screws at the joints of the door. The assistant must hold the door at all times so that it does not fly out with the hinges. The curtains still have to be changed. Even if the door is removed and the curtains remain in place, they will be damaged.

To remove the platband, you need to slip an ax blade under it. After that, you need to knock on the ax with a hammer, and drive the blade as deep as possible. The hatchet will become a lever with which you can remove the platband from the box.

You can take out the wooden box using two options.

1. If you can remove the fasteners (at the junction of the box and the wall), then the box is removed after that. And you can also remove the fasteners by tapping with a hammer on the entire structure. In order not to deform the wood, you can use a substrate in the form of a board.

2. If the internal fasteners cannot be removed, you need to cut the box in the corners and take it out in parts. You can use a hacksaw for cutting.

After this procedure, you need to clean the walls from the remnants of fastening and dirt.

After removing the door, the hinges should be inspected and lubricated if the hinges are suitable for re-installation.

For this, work is carried out according to a specific algorithm.

1. First, the hinges are cleaned from small debris. The surfaces can be cleaned with a cloth soaked in gasoline.

2. Then the hinges are wiped with a dry cloth.

3. All elements are lubricated with mineral oil. This procedure can also be carried out when the door is in place, if they begin to creak or do not close properly.

Experts recommend using only special compounds for lubricating the hinges. The lubricant must be free of solid particles that could damage the mechanism.It is better to immediately purchase a special oil that is also suitable for lubricating window hinges. It is necessary to lubricate the hinges with oil from time to time so that they do not deform and perform their main function for a long time.

Reinstallation of doors is carried out depending on whether the box was removed or not. If you need to put only a new blade, then the installation is repeated in the reverse order with respect to dismantling. The most important thing is not to deform the new door or frame. To do all the work correctly, you should ask another person for help. The first master should hold the door while the second does the bulk of the work.

The easiest way is to re-install a wooden door. Here, the new design is simply put on the hinges, and then adjusted to fit the frame. The adjustment is carried out using rubber gaskets; it is also important to take into account the dimensions of the door frame.

It is much more difficult to install the box. First, you need to clean the walls of various debris, and then start processing them. It is necessary to drill new holes for the joints, it is better not to use the old ones. Boxes made of PVC or wood are inserted in about the same way: first, the box must be assembled, and only then mounted in the doorway.

Wooden frames will perfectly hold onto self-tapping screws. Sometimes concrete base nails or liquid glue are also used. PVC panels must be fixed to a strong frame - special metal plates.

The gaps on the sides of the frame must be closed with polyurethane foam, which will also give the structure tightness. Further work depends on your desire: you can install platbands, paint the door and carry out other procedures.

Install a new door only after the foam has set.

How to remove the door from the hinges on the balcony and loggia, watch further